Command Parts

*Kohler 2 barrel Carb $254.00ea* *2 barrel carb and intake Combo $345.00ea* *Add the V-stack for $50.00 when you* *purchase carb and intake combo (Carb, Intake, V-stack) $395.00ea* *Plastic intake Flows more than stock CH intake* *$45.00ea*	*2 barrel intake* *$96.00ea* *CV (verticle intake) intake Flows almost twice as much as stock intake,* *Will work on horizontal commands with our adaptor.* *$95.00ea*	*2 barrel Velocity stack and Air filter adaptor* *$60.00ea* *1\2" steel adaptor used to adapt downdraft carbs to vertical intake* *$46.00ea*
*1" aluminum spacer\adaptor for downdraft carbs.* *Used to adapt downdraft to verticle intake or as a spacer for horizontal setups. Outer holes will have to be drilled out to use as a spacer.* *$46.00ea* *Stronger Valve Springs w\ retainers , use with cast cams.* *$50.00 set* *Roller Lifters $105.00 set (4)* *Cast Reground cams. $275.00 ea with your core* *Core charge $50.00 More duration and lift than stock.* *Lifts available .310, Duration is 260deg.* These cams have a fast ramp and more lift than stock so you will have to take care to insure that valve srings do not coil bind and check valve clearance to pistons on modified heads and flat top or welded pistons heads. If you have question call us for help. *2 into 1 header $92.00ea* *Intake gasket $2.50ea* *Valve Stem Seal $3.50ea* *Billet Valve Covers with gaskets and Screws $140.00 Set* *Steel Location Dowel. Fits in the block where the head bolts go to help properly align the heads. $3.50ea*	*Command downdraft carb Velocity stack* *$50.00* *Stainless Steel valves* *Stock diameter and length or* *Oversize diameter and .300" longer* *$130.00 set* *Roller Rocker Set up. Comes with everything you need* *Some machining is required.* *$135.00 set* *Stock command high compression heads. These heads are Stock OEM parts and have a tighter combustion chamber than stock 20-25hp heads.* *$230.00 Set* *Stock length command Billet Rods* *$125.00each* *2 into 1 header side exhaust, specify right or left when ordering* *$125.00ea* *Breather gasket $5.00ea* *Valve keepers $10.00 set for 4 valves* *Header Wrap, Roll is approx the siz e of a roll of duct tape.* *Plenty of wrap for two or three tractors* *$20.00 roll*	*Dual valve springs with retainers. Not recommended for use on cast cams.* *Works well on steel cams $65.00 set* *Adjustable Push Rods, with inserts* *$35.00 set (4)* *Hyd or Solid Lifters. Hyd lifters are stronger then stock.* *Solid lifters have a .012 oil hole in the face* *provides more lubrication to the cam.* *$55.00 set (4)* *Copper head gaskets Available in* *18-22hp .031 or .062* *25-27hp .031 or .062* *$21.00 Set (2) .031* *$25.00 Set (2) .062* *Rod Bearings Set of 4 $43.00* *Exhaust Gasket $3.00ea* *Oil Adaptor Gasket $3.50ea* *Flywheel Key standard $4.00ea Offset keys to advance timing $7.50 each* *Ignition coils Hi Rev. $45.00ea* *Steel ADjustable Flywheel $275.00ea* *Steel Non-Adjustable Flywheel $175.00ea* *Billet magnet for flywheel $62.00ea*
*New Under Frame Header Pipe. Fits Command engines, goes under the frame. $195.00*	*Custom Intake for 2 barrel. 1-1\4" Tubing with flange to accept stock 2 barrel. $150.00ea*	*Custom intake for Command Downdraft Carb. 1-1\4 inch tubing with flange for stock downdraft carb.* *$150.00ea*